MXR

• Highly responsive full spectrum distortion
• Bass, Mid and Treble controls
• 100% Analog, True Bypass
• A full range of dirt, from low-gain overdrive to modern metal
• True bypass switching
• Roadworthy housing
• Bulletproof componentry

• Analog bucket-brigade technology
• Separate Bass and Treble controls
• Flanger and X-Over for added tonal flexibility

• Overdrive with just the right flavor of non-brittle signal breakup
• Organic, germanium- powered clipping
• Goes from subtle overdrive to fuzz-like saturation
• The MXR Distortion+ is powered by one 9-volt battery (remove bottom plate to install), a 9-volt AC adapter such as the Dunlop ECB003/ECB003E, or a DC Brick™ power supply

• Six meticulously crafted reverbs in one pedal
• Audiophile quality analog and digital audio paths
• Dry path is 100% analog
• Studio-grade low noise floor
• Trails Bypass mode lets effect ring out after turning the pedal off
• Expression pedal jack for foot control of all knob settings
• Stereo In/Out capability when using TRS cables
• The MXR Reverb requires 9 volts (240mA) and can be powered by the included Dunlop ECB003/ECB003EU adapter or the Iso-Brick™ Power Supply. This pedal cannot be powered by a battery.

• Preamp and gain boost pedal for electric guitar
• Based on the input stage of the Echoplex EP-3, with the exact same signal path
• Add up to 11dB of gain to your sound, with warm overdrive at higher settings
• Powered via 9V battery or optional adapter (sold separately)
• Keep your tone intact with True Bypass switching

• Classic studio compressor in a Phase 90-sized pedal
• CHT™ Constant Headroom
• Technology for clear, clean performance
• Ten Gain Reduction status LEDs
• True bypass
• The MXR Bass Compressor is powered by one 9-volt battery (remove bottom plate to install), a 9-volt AC adapter such as the Dunlop ECB003/ECB003E, or a DC Brick™ power supply.

• Rich, warm analog tone
• Late '60s/early '70s crunch
• The guts of our BC-108-loaded Fuzz Face in a more pedal-board friendly shape

Packed into a standard MXR housing that's built like a tank, it's easier to use and delivers higher fidelity signal reproduction than any other looper of its type. Highly engineered for incredible sound quality, it comes packed with features in a pedal board friendly housing and can be as simple or complex as your needs dictate. Just plug in, power up and start recording an unlimited number of layers up to 6 minutes long (that will be stored even when the pedal is off).

• Two independent analog octave voices
• Mid+ switch boosts selectable midrange
• Constant headroom Technology (CHT)

• Separate INPUT & OUTPUT level controls
• 3-band EQ section with sweepable midrange
• Studio-quality Direct Out

• Overdrive pedal made exclusively for bass
• Get big, punchy, tubelike bass tone
• Volume, Tone, and Drive controls
• Clean control lets you blend your clean signal in with the overdrive
• Compact, pedalboard-friendly form factor
• Powered by one 9V battery or AC adapter (not included)

• Vintage Echoplex EP-3 tape echo warmth and modulation
• Audiophile quality audio paths
• 100% analog dry path
• Studio-grade low noise floor
• Age control varies delay tone from pristine to dark and dirty
• Delay control provides 65–750ms of delay time
• Tap jack provides up to 4 seconds of delay time with external Tap Tempo Switch
• The Echoplex Delay requires 9 volts (240mA) and can be powered by the included Dunlop ECB003/ECB003EU adapter or the Iso-Brick ™ Power Supply. This pedal cannot be powered by a battery.
• To combine the EP103 with the EP101 Echoplex Preamp for the full Echoplex EP-3 experience, simply run the EP101 in front of the EP103

• Hand-wired circuit board built with original-spec 1974 components
• Warm analog tone
• Select resistors paired with hand-matched FETs
• Adorned with script logo
• Simple one-knob operation
• Deep, rich phasing

• Classic studio compressor in a Phase 90-sized pedal
• CHT™ Constant Headroom
• Technology for clear, clean performance
• Ten Gain Reduction status LEDs
• True bypass
• The MXR Studio Compressor is powered by one 9-volt battery (remove bottom plate to install), a 9-volt AC adapter such as the Dunlop ECB003/ECB003EU, or the DC Brick™ and Iso-Brick™ power supplies.